Triplett 9320-A Uživatelský manuál

9Triplett Model 9320-A5: SPECIFICATIONS5.1 Display: 0.58" (15mm) high LCD5.2 Display Resolution: 4000 counts, 0000 to 39995.3 Overrange Indica

10Triplett Model 9320-AtnerruCCASMRTegnaRnoituloseRycaruccAA004A1.0 ± )DSL5+gdr%0.2(A0001A1 ± )DSL01+gdr%5.2(:noitcetorPdaolrevO sces06nahtsselrofxamA

11Triplett Model 9320-AtseTytiunitnoCdnaedoiDegnaRsetoNtseT.V999.1.xorppaotpuVniegatlovedoid.xorppasyalpsiD.V8.2tuobaegatlovtiucricnepO.Am4.0tuobatner

12Triplett Model 9320-AFIGURE 1FRONT PANEL OF 9320-A12346911121310578

13Triplett Model 9320-A6: 9320-A FRONT & REAR PANEL, DISPLAY DETAILS1) Centering Marks – Position the conductor within the jaws at the intersecti

14Triplett Model 9320-A11) D. HOLD / LIGHT Button – Holds the reading in the display when the D-HOLD button is pressed and released. appears i

15Triplett Model 9320-AHold Annunciator – This annunciator is displayed any time the holdmode is active.REL Annunciator – This annunciator is displaye

16Triplett Model 9320-AnF, mFCapacitance (Farads) Annunciators – These annunciators aredisplayed whenever Capacitance is being measured. The displayed

17Triplett Model 9320-A1415FIGURE 4BATTERY COVERRefer to Figure 4 for a view of the rear of the Meter.14) Battery Cover Screw – This screw secures th

18Triplett Model 9320-A7: PREPARATION FOR USE7.1 Before using the Meter, familiarize yourself with the instrument and this manual. READ AND R

1Triplett Model 9320-ACONTENTS PAGE1. Introduction 12. Safety Rules and Warnings 2 - 73. International Symbols 84. Product Features 85. Specifications

19Triplett Model 9320-A7.7.2 Battery Replacement Remove the 9V battery and replace it with a fresh one.7.7.3 Battery Cover Installation

20Triplett Model 9320-A8: GENERAL MEASUREMENT PROCEDURES8.1 This section describes general operation of the Meter. When making measurements o

21Triplett Model 9320-A Turn the equipment or voltage source on and take the required reading. DO NOT HANDLE OR TOUCH THE METER, TEST L

22Triplett Model 9320-A9: SPECIFIC MEASUREMENT PROCEDURES9.1 AC and DC Voltage Measurement WARNING!!!If the input voltage is higher than 1000VDC (CA

23Triplett Model 9320-AFIGURE 5MEASURING VOLTAGERead the voltage on the display.If the meter is set to Auto, it may display overrange OL momentarily w

24Triplett Model 9320-A9.2 Measuring AC or DC CurrentRefer to Section 7.0, Preparation For Use, and Section 8.0, General MeasurementProcedures, befor

25Triplett Model 9320-AFIGURE 6MEASURING AC AMPSIf it is desired to hold the reading, press the D-HOLD button so that the annunciator is visible on th

26Triplett Model 9320-A9.3 Measuring Resistance WARNING!!!Do not apply voltage or current to the meter when it is set to Refer to Section 7.0, Prep

27Triplett Model 9320-ARead the resistance on the display. Note the range annunciator (Ω, k Ω, or M Ω).If it is desired to hold the reading, press th

28Triplett Model 9320-A9.4 Diode Test WARNING!!!Do not apply voltage or current to the meter when it is set to Refer to Section 7.0, Preparation For

2Triplett Model 9320-A2: SAFETY RULES & WARNINGS2.1 Read all instructions in this manual before using this meter. Failure to do so may res

29Triplett Model 9320-Athen pressing the SELECT button until the annunciator appears in the display.Make certain that the annunciator on the disp

30Triplett Model 9320-ABefore testing a capacitor, make sure it is discharged. Use an approved methodfor discharging the capacitor. Improperly dischar

31Triplett Model 9320-AIf the V position is selected, set the meter to AC volts by pressing the SELECTbutton, then connect the test leads to the sig

32Triplett Model 9320-APlug the provided temperature probe into the COM and VΩHz jacks, observingproper polarity. Apply the tip of the probe to the su

33Triplett Model 9320-ATo exit this mode, press and hold the MAX / MIN button until the meter beeps andthe MAX and MIN annunciators disappear. All mem

34Triplett Model 9320-AConnect the test leads to the resistance to be measured.Press the MAX / MIN button. The meter will memorize the MAXimum and MIN

35Triplett Model 9320-A10: MAINTENANCEYour Triplett Model 9320-A Digital Clamp Meter is a precision measuring instru-ment and, when used as described

36Triplett Model 9320-A11.2 Model 101-G Line Separator (Triplett PN: 3264) Allows easy measurement of current in standard AC line cords.• F

3Triplett Model 9320-A2.10 Make sure test leads are properly inserted and seated in the meter’s input jacks. A loose test lead may cause the us

4Triplett Model 9320-A2.20 Do not rotate the Function switch with the test leads connected to the circuitry to be tested. Doing so may damage

5Triplett Model 9320-A2.30 Do not modify the meter. Changing the design may make the meter unsafe and may result in injury to the user.2.31 U

6Triplett Model 9320-A2.38 If there is any doubt about the condition of the meter (i.e. safe vs unsafe), remove the meter from service and sec

7Triplett Model 9320-A2.46 Avoid usage near strong RF fields (radio or television transmitters, walkie talkies, cellular phones, etc.). The me

8Triplett Model 9320-A3: INTERNATIONAL SYMBOLSThe following International Symbols may be used in this manual and on the caseof the meter to identify,